Quantcast
Jump to content
BigBen835

Milk Truck Rolled in Water!!

Recommended Posts

Topic Originally Created on Tow411 in October of 2008.

 

Got a call from local sheriff dept. for a HD recovery of a partially loaded quad axle milk truck in the water.

 

Described as 20' down, and approx. 30-40' away from road in @ 4-5' of water. Driver stated had @ 18000# milk on board. Total vehicle weight of est. 50000 lbs. I took my 75 ton, and Justin came in on his Sunday off to help with the 60 ton. Upon arrival the road was wide enough to get one side of the outriggers out and hug the far bank. The truck did a complete roll and came to a rest drivers side down. Driver was OK. The road had no shoulder on either side and near vertical rocky face. During the upright procedure the road cracked and more of the bank caved in. The local varmints had made a tunnel system under road. As the truck settled on its wheels the left side outrigger went thru. After that, a vertical lift was out, no good base. The adjacent property owner granted permission to her yard for a long winch thru swamp. Justin fit in the waders so he got elected to be in water. He spent 3+ hours in water rigging, spring fed and very cold. A 220' winch to yard and a little help from the 75 ton from the road, winch the 60 ton out of its holes, back to shop---- done.

 

Truck was towed from scene to customers shop one mile away, to be unloaded into different tanker. Total time for recovery was 10 hours port to port. The scene was restored approx. 2 days later after the ground dried up a litlle. All grade 120 rigging used, for winch. I know someone will ask why the outriggers were out during winch, I don't know but the ground was so soft and wet there was no pressure on them. No equipment breakage, and a round of applause from on lookers.

 

Comments & suggestions?

 

26f351ba5c1ba1887586425c11ad00c10579f47.

d702542538a9c7184d41788814c167da12686af.

59135e7a5efaa59e720b4c391fa1f7d3357f84a.

2b325de5e3a7e792436151e91aa82d331df2e57.

9d9359165229a0e77bbb4b8e164018346177608.

d141525daf754b1722a8c06d8a475b8aa36e872.

04d15250af7b4515d61f15daabf94da28dd1db3.

7e0357285ab5a4ba7d074d1210912c6e764f003.

27615459aa7245113f6ef72c17f620e77ecf7cf.

5a515954a57c4f19d047a7effcab52bc9ccca23.

7d515c5eac75451b285ed41aa341664d78ce0c2.

75515457a4794a1e79667fe7b40d2a573ba17b4.

44325e651ba767bb48f1485eae8175b82022def.

98215050a6704c119530120fc389fac8b7dc325.

2b52551525a3e71540e1e2681cb2c01d26f21ba.

f5815f5ba3794613fe44793f6a6a27bd95a792e.

 

Carter & Sons Towing tubebronze.gif said:

Nice recovery, that swamp looks nasty. Also like the saying on the outrigger.
Jason

 

Morgan1 said:

Nice truck and nice picks.Areend you afraid those stabilisers breake?The man ho put the gains around need an cleaning i think

 

Michael212 tubegreen.gif said:

Nice Job Ben emoticonthumb.gif
Michael Myers
253.588.1757 ext 150

sigmichael212.gif
 
BigWheelRecovery tubeplatinum.gif said:
NICE JOB GUYS ,,Thanks Eric
d66e94b8394f8b0e098ffb1baf38f9b0d701d13d
 
Heavytowman12 said:
Looks like a recovery most of us would like to have done. Nice work!
 
WyomingTowPro said:
Hey Nice job out there. gotta love a good challenge.... Do have a question. Based on the moisture.were u able to pull out of the yard on your own or did ur other truck assist u getting back to the hard surface??
 
Heavytowman12 said:
Nice job , Nice looking rotator also, does your truck have a canadian spread. ? It looks wider than normal
Richard Guttmann 
 
BigBen835 said:
Yes, it is a spread, and no we had to pull it out with my truck. It was very wet, the side legs were down a few inches, when we started winching they were not touching the ground, but i had a pretty heavy lean to the left, that's why i put them out. I had one shot getting in and i was a little crooked. Once it started to come out it was a straight pull off rear. I never thought about them again. The ground was soooooo soft it was just peeling the sod up, no side load. The taillights we built in shop. Thanks for comments.
 
wm060071 said:
nothing like a good pull!! Stupid question but Did you have to pull the wrecker out. You can see that the out riggers went down at the beginning. But don't it make more sense to have them down for more surface contact!!! Or will they bend?
That's awesome !!!
 
TOWAHOLIC tubegreen.gif said:
Cool job. that's the kinda jobs ya dream about. woulda been a cool pick too!
c0dcb0e13bcfc8dca900777bf055dcb245af7420
 
NR8171 said:
another stupid question> why not put the legs down on a pull like that?
 
Bighook18 said:
Great job...I have a question.. who was the "lucky" one to rig the front axle?? WOW....
"I always got my hook.."

Todd Pell
 
BigBen835 said:
Big Hook, Justin fit in the waders, so guess what!!!! 648.gifHe had to rig everything by feel. He did a heckva a job, the water was 50--ish degrees. The bulk of the time was rigging and pulling lines. The water was just a few inches from the top of the waders. Literally no bottom just endless muck. I threw down the rigging, and started pulling cables thru the slop.
 
 
 

Share this post


Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


  • Welcome to TowForce.net

    Wanting to join the rest of our members?

    Feel free to sign up today.

×
×
  • Create New...