Quantcast
Jump to content

Leaderboard


Popular Content

Showing content with the highest reputation since 11/23/2018 in all areas

  1. 5 points
    Eric Fouquette

    Relax and Go Fishing

    Just to see what you can catch Source:
  2. 4 points
    jrtowman

    Big changes in a year!

    Top picture was a year ago today and the bottom is what it looks like now.
  3. 3 points
    TowZone

    6000 Member in only 120 Days

    With the exit of AWDirect from the Towing Information Network after more than 14 years as a Tow411 Sponsor. I needed to find another “Major Sponsor” to support our network. While attending the NTEA Work Truck Show last week it just happened a “Well Known Company” offered to add their support and participation as a Platinum Sponsor on the New Force in the Industry. They had only one requirement and that was, we must double our membership within 120 days. At that time we had just reached a goal of more than 3000 members in 15 months. The next goal was set at 6000 members by the end of 2019. To do this in 4 months is nearly impossible as it will take 25 new members each day. This “Well Known Company” set the bar high, but that is nothing for an Industry that in general sets the bar high every day. If your not already a TowForce.net member will you register today and get us closer to this nearly impossible goal. Is it possible, yes however it would take everyone that watches this message board to join. You can join using various methods, there is no cost to join. DAY 1 - 58 New Members - Day 2 - 41 New Members - Day 3 - 20 New Members - Day 4 - 7 New Members - Day 5 - 6 New Members - Day 6 - 7 New Members - Day 7 - 2 New Members - Day 8 - 7 New Members - Day 9 - 7 New Members - DAY 10 - 4 New Members - Day 11 - 11 New Members - Day 12 - 5 New Members - Day 13 - 7 New Members - Day 14 - 10 New Members - Day 15 - 6 New Members - Day 16 - 8 New Members - Day 17 - 5 New Members - Day 18 - 5 New Members - Day 19 - 4 New Members - Day 20 - 7 New Members - Day 21 - 9 New Members - Day 22 - 5 New Members - Day 23 - 0 New Members - Day 24 - 17 New Members - Day 25 - 3 New Members - Day 26 - 2 New Members - Day 27 - 2 New Members - Day 28 - 4 New Members - Day 29 - 16 New Members - Day 30 - 3 New Members - Day 31 - 6 New Members - Day 32 - 13 New Members - Day 33 - 4 New Members - Day 34 - 5 New Members - Day 35 - 6 New Members - Day 36 - 5 New Members - Day 37 - 2 New Members - Day 38 - 5 New Members - Day 39 - 7 New Members - Day 40 - 27 New Members - Day 41 - 4 New Members - Day 42 - 0 New Members - Day 43 - 4 New Members - Day 42 - 1 New Member - Day 43 - 3 New Members - Day 44 - 15 New Members - Day 45 - 1 New Member - Day 46 - 6 New Members - Day 47 - 3 New Members - Day 48 - 4 New Members - Day 49 - 2 New Members - Day 50 - 2 New Members - 410 Current Count 3386 Members Average 8.2 a day - Short 17 Members a day.
  4. 3 points
    EdsTowing

    Annnnd Another Rollover...

    Jeez 3 rollovers this weekend...all with clean ups too! This one tumble rolled in a private community w/ 25 mph speed limits... She said she swerved because a Goffer ran across the road... They cleaned up the roadway and told the Officer we would be back in the daylight to do a proper clean up.... Destroyed a new Journey...Customer called me to ask if it was driveable? I asked weren't you in it & she said yes....No...No it's not driveable...
  5. 3 points
    As of recent, i think both of us thought the days where over, but here we are. Nothing has been more enjoyable than teaching with this guy, Jeff Martin We at times argue like brothers over class logistics and stuff, but you folks see the end result. Add the other folks and we have a great time. Nobody, I'd rather have by my side. Love ya brother
  6. 3 points
    EdsTowing

    Another Rollover...

    Customer trying to avoid a stopped car & ran off the road. It hit a stone wall & flipped over... A nice "quicky" in & out job...
  7. 3 points
    BigBlonde

    AT ShowPlace Las Vegas Roll Call

    Glenn and myself will be there
  8. 3 points
    ttroseledge

    Progress on 70 Ton Rotator

    There's a lot of red to get rid of, new body and front boxes taking shape, new proportional remote, adding 35k D P 2 speed drag winch and rear 3 stage outriggers. Thanks to TJ ,Jay , and ,Bill Wong UPDATED: More progress shots on 70 ton dewalt, new sides taking shape, unit sanded, braces added to boom base, all new hoses in place, additional valve section installed in valve body, ready to add 35k 2 speed drag winch, new proportional remote ordered.
  9. 3 points
    Randall Resch, Alpine CA. - Operations Editor, American Towman Magazine, retired police officer San Diego Police Department, and Senior Off-Road Recovery Engineer, Naval Special Warfare since 1967. Thanks Ron and Chris for providing the Number one forum that brings towers together.
  10. 3 points
    I'll have to get a pic of it tomorrow George. We took their unit and welded a receiver tube on it. Now we have a pintle hook adapter and a 3 way ball assembly. We also install a factory ford trailer plug in the rear. It makes for a clean install for a 4 wire & 6 wire plugs. She got her new suit on today... I think it looks good....
  11. 3 points
    EdsTowing

    Rollover w/ Plenty Of Rolls....

    Well Ron you're right...no yellow trucks but they were there in spirit! I owe a lot to those people and Big Wheel changed the way I do things literally the day after my 1st class.... nearly 10 years ago. And when I presented my invoice to a typically difficult insurance company, they didn't have a single complaint. My connections made back then have & will continue my business's prosperity for years to come as well as friendships that are priceless. Stuart you're right...I was dreading these rolls as soon as I found out. I knew if I was to drag them out the back and load them on a trailer or carriers, they would be junk for sure. To make matters worse, they have a small hole (7/8") in the middle so rigging to them could be tricky... I knew it would be difficult to lift that dead weight in such a confined area but handling them was potentially dangerous . Like John said, I was concerned that they would move around when the trailer dropped and @ 6000 lbs each...they can make a difference! Wet set it pretty easily, I think I have a video of it...a slight bounce but not much drama. The rolls were damaged some but from their initial movement. They decided to scrap the load in the end so it is what it is. Thanks Randall. We were taxing the Tator pretty good so I decided to add my second line off a block to the drives just in case. It turned up to be a good idea because it was starting to stall the auxiliary winches and the main boom winches were getting the outriggers "Light". A lot of guys really push them but I don't know this truck well enough to exceed the platform. That added line made the difference though to get the initial lift to start & then from there it was like text book. Thanks for all the comments.
  12. 3 points
    goodmichael

    Just a suggestion

    I have a suggestion that I believe could promote a safer work environment for all that read this forum. Would it be possible to start a forum entitled, "Today I made an attempt to be a safer operator by...… This will allow those people who practice safety and proper procedure to share their experience, knowledge, education, and training. One of the suggestions just might prompt someone out there somewhere, to do something different, to put another tool in their mental toolbox, to zig where they normally would have zagged. Who knows, just one person implementing a safe practice or procedure could save someone, somewhere from getting seriously injured, or from someone from having to make that phone call everyone knows that they might have to make, but cringes at the thought of having to make the call.
  13. 3 points
    Here's sad news of a tow operator fatality that occured early this morning making this the first fatality of 2019. According to the news, tow operator, Pat Sisneros, of Madrid Towing, was struck and killed as he attempted to assist a NM state police officer. According to State Police, a semi-truck crashed into a State Police vehicle just before 1 a.m. Police say Pat Sisneros stopped to assist the officer when another semi collided into Sisneros' tow truck, killing him. All lanes on I40 Eastbound MM 157 were closed due to the motor vehicle accident involving the second semi-truck. It was also reported that 20-degree temperatures caused lanes to be were extremely icy. Details are few and an investigation is being on-going. My prayers are with the Sisneros' family and the company Pat worked for. https://www.kob.com/albuquerque-news/albuquerque-roads-slick-and-dangerous/5196197/
  14. 3 points
    While this is not the time for such discussion, it must be discussed before an action plan can be put it place. "My gut feeling is the electronic logging mandate, although artificially, has placed increased pressure on drivers to "push through" because of that set in stone digital clock staring them in the face." I have been hearing this louder and louder that because of the ELD. The dispatchers are pushing the drivers harder. One trucker stated he is one of the few English speaking drivers in the company and he has to routinely tell the person is is speaking with the speak English and to text in English. So, drivers are now be pushed harder. Wasn't that what the CDL and ELD was suppose to stop?
  15. 3 points
    We are entering the apex of the Christmas season this weekend. Colleges are completing final semester exams this week. I have one tomorrow, my last one, thank you God. Many will begin to drink as well as use illegal drugs under the guise of "celebrating." Please be extra cognizant in every step of every process you complete to limit the time you are in harms way. It is not a race, nothing you do is worth risking your life in order to save a few seconds. Your family needs you, your community needs you, and this industry, despite all of it's issues, needs you as well. Each and every one of you is a valuable resource to those close to you. There is no tire, or vehicle for that matter that is worth you risking your health, well being, or life over. that car or tire can be easily replaced, you can not be! I hope every one of you has a blessed, safe, and meaningful Christmas as well as a bountiful 2019. I personally have had a rough 2018, and am ready to close the chapter and look forward to a great 2019.
  16. 3 points
  17. 3 points
    annettemcd

    2018 Motor Club Ranking

    1. Geico --pleasant dispatchers who really seems to care about motorists, fast payment, easy invoice submission, decent rates 2. AAA (NCNU) --When we were part of MountainWestAAA and that was great, now it is Northern California, Nevada, Utah, Arizona, Alaska, Montana, and Wyoming and nothing is the same. 3. Agero --commonly confused about location and destination (a common one has been closed for 6 years), complex procedure for requesting extras, short pays not uncommon, poor communication, commonly lies to us and to motorists about the covered distance. Only 6 jobs so far this year with any other motor club.
  18. 2 points
    Our Leader, Steve Sedberry is always willing to jump in and work beside each of the employees.
  19. 2 points
    There is no car that is worth putting another human being's life in jeopardy. TDLR would do well to stop just being a money tick and do something worthwhile and mandate that those who repossess vehicles or collateral at least be familiar with what a breach of the peace, illegal acts, as well as the fair debt collection practices act is all about. This incident at least fails the breach of the peace standard. I am not kicking a person when they are down, but a person died for a piece of crap hunk of plastic and tin with a mile of copper wire thrown in. Every car is a piece of crap compared to a human life. I have repossessed vehicles and been in a tight spot or two. If in doubt I will release the car. I found it once, I will find it again. There are 7 million car notes that are 90+ days so even if I do not, they are like Lay's potato chips, they will make more.
  20. 2 points
    Njsss

    A Medium With A Light

  21. 2 points
    Orcas Tow

    "Hiding" Towmate Transmitter

    I hard wired mine in my overhead light bar, dry & high up for a good un obstructed signal.
  22. 2 points
    someotherplace

    Stuck In Park, 4WD & Park Brake

    Yep, no more disconnecting linkage on RAM trucks since 2011-2012 I think. They *look* like you can disconnect it but you can't shift, as you discovered. And, on Mopar fullsize cars since 2008. BUT, there is a release inside the vehicle on most. I usually don't mess with them being full-time PPI as I do not have keys. However if you're on a consent tow there is a release cord inside the cars console, and on the trucks I believe it's to the left of the column in the dash after you pop a panel off. Richard
  23. 2 points
    rreschran

    Lets Lower The Statistics...

    Thanks Ed ... I will help to spread your message at the upcoming tow shows. If motorists can't see the arrowboard or its reflective striping, we towers are really working a lost cause. R.
  24. 2 points
    All towers should have TIM training for obvious reasons, but also to have that coveted certificate in their personnel/training file when it comes time to defend a driver and the company against civil lawsuit. A recent high-dollar California lawsuit was based on a tow operator's training as a Freeway Service Patrol operator being sued. His training was heavily attacked, but the tower had FSP, CHP, and current TIM training to uphold his experience. Four-hours time to complete FREE training is chump change to a multi-million dollar lawsuit. And, yes, I am a TIM instructor in California. R.
  25. 2 points
    EdsTowing

    Surprise, Surprise, Surprise....

    Got home from the Florida show yesterday & my son surprised me with a new truck! Two of my grandkids explained all of the technology & how stuff works.... Oh and "Dallas" waiting to go for a ride. My wife & I are blessed with great kids & grandchildren....
  26. 2 points
    Donny Callahan

    Pictures Tell The Story

    Pick, rotate, lay down, load and haul oversized allenstowing said: Did it grow between pis 2 and 3? Looks good. Donny Callahan said: I wiggled my nose and made it shorter... Lol... It was 20' high and 10' wide bulldog1635 said: very impressive. looks very close to the wrecker. what size NRC is that ? al, bull dog Donny Callahan said: It's a 40/50 SR The tank really isn't that close... The pictures turned out funky... MTA415 said: sweet graphics!
  27. 2 points
    Ron ... I wholeheartedly nominate Steve and Doc Calitri of American Towman Magazine, and, Clarissa Powell, Tow Times Magazine, for their career participation to the towing and recovery industry. Their publications and tow show presentations have provided towing and recovery professionals the platform in which to share everything having to do with the industry. They've created environments that bring tow professionals to together throughout the world. Thank you for your contributions to the industry. You are true leaders and this recognition is due. Steve, Doc and Clarissa have undoubtedly influenced myself and millions of readers on an international scale ... no small task. I believe this award is befitting to their leadership and committment to the towing and recovery industry. R.
  28. 2 points
    ESC

    Recover This -

    This one is in the water..... assuming it at least has liability coverage on it, it would be a pretty easy one to get paid on. Personally, I would call in a friend with a rotator and have them set it on my bed. I would also make sure to have some absorbent pads and booms ready to absorb any fluids out of the water. Lots of pictures.
  29. 2 points
    Njsss

    Newest Addition

  30. 2 points
    Littletow

    AT ShowPlace Las Vegas Roll Call

    I and APTRA will be there in full force! Stop by our booth!
  31. 2 points
    Tow411

    Some Suburban Wrecker Nostalgia

    Topic Originally Created by wreckmster in June of 2007: ere are some photos of trucks no longer with us. Our First wrecker... "HOOK" GMC with a 30 ton Wreckmaster rig Our second truck "THE BOSS" It was a slug. 318 Detroit engine(no turbo) with a 30 ton Wreckmaster rig with extendable booms. Our third truck. "BEAR" GMC with 25 ton Wreckmaster rig Early Fleet photo That's little ole me on the left with the baseball hat. My brother is next to me, then my father followed by two former employees. truck 4 Newer cab and chassis on original 30 ton Wreckmaster bed (loud Air starter) LOL Truck 6 we built for my brother. It was a 1980 brigadier and had a 25 ton wreckmaster rig with custom length booms. they were about 2 ft longer than the standard boom. Great towing unit Truck 6 is towing my first truck I built and drove.Which I drilled many a hole in the frame to build. Frame drills were heavy back then. It is also a Brigadier, but had the 30 ton body with the extendable booms from truck 2. My truck is being towed because I had a severe knee injury and would be out of work for awhile. He was towing it back to the shop. GMC General 30 ton unit (great truck) I spent most of my time in this unit. Our most disappointing truck 97 Freightliner with 25 ton Jerrdan unit I'll see If I can find some other pics FMS Mike said: Awesome Pics!!! Them are some hosses!! Michael ------Michael Vibert------- Da Wash Boss said: Those are some really nice trucks. Were you guys one of wreck masters biggest customers,,,,, Just some really nice units there. That road boss looks good as does the General. I notice in the first picture that "N" model Ford box truck in the background,, thats a nice truck also. Thanks for sharing you guys paid your dues over the years, nice trucks then and some nice ones now as well. Good luck in the future. Danny Cassello - TRPC - East Hartford, CT OldHolmes460user said: very nice collection of pics. How old is your family business? underdog said: Those were all great trucks. Bet you wish you kept at least one of them! Stay safe, Rich. wreckmster said: Thanks for the comments. Our Business was established in 1976. I do wish we still had the GMC General. All around good towing and winching truck. Rode like a brick though with the Hendrickson rears.. (Ouch) Gale25yrs said: Why was the Freightliner such a disappointment? Too heavy? wreckmster said: The Freightliner was just a trouble truck. It was cheaply made. The doors echo'd when you closed them. The visor kept falling off and cracking the roof. For some odd reason it squatted really easy even with increased air ride pressure. It had one of the early style Jerrdan rigs with the older lift cylinders. You know the ones that if you moved the boom under load and it was out of it's channel, the boom would shift and take out the fog light. You could use the winches, but not the boom under load. We had alot of problems with the rear axles. We would go through about 2 axles a year and that was with a good operator. It towed pretty well though, just wasn't very dependable. It struggled with dropped trailers and since the boomed moved, I was hesitant on send it out. I just cut my losses and sold it for a bigger truck. The tandem axle Pete/35 ton Jerrdan we replaced it with has been a good combination so far for the most part. Michael212 said: Thanks For Sharing! It's always pretty cool to see where you started and see where your at today. Keep up the Good Work! Michael Myers Heavytowman12 said: You had nice equipment back then just like you do now. Wreckmaster made a real nice rig.Operated one for a few years on a Autocar.Those Briggaders were real poplar trucks then. Bet you wish you still had one of those. Just for keep sake! fredstowingnj said: I remember the old Wreckmaster plant in Cranbury,NJ. Da Wash Boss said: Hey Fred, I never knew thats where the wreck master plant was. If I remember correctly I think Roadmasters Towing had some dodges or gmcs with wreck master units on them. I am not sure thought maybe you would know if not I bet Steve or Bob remembers. They were nice trucks. Danny Cassello - TRPC - East Hartford, CT geartow said: now if i could find parts for a wreckmaster 25 ton id love it FredsTowingnj said: Don't really know much about RoadMasters Steve or Bob would know more then me.But yes Wreckmaster's plant was on Cranbury South River Road in Cranbury,NJ Auto Rescue said: Worse yet I remember when they built it Recovery Inc said: Those wreckmasters looked alot like Holmes were they close in competition. Great pics thanks for showing. Chris Fontaine Interstate Towing Da Wash Boss said: QUOTE: "Those wreckmasters looked alot like Holmes were they close in competition." They may have looked close and they were great units but,,,,, There is nothing that comes close to a holmes. How many agree with me on that about Holmes. Danny Cassello - TRPC - East Hartford, CT wreckmster said: not much of a difference between the two really. The Wreckmaster winches were backwards.....basically they were practically duplicates. I wouldn't say Holmes was any better or worst.. I personally put my Wreckmasters to the test. They faired very well.. wstowing11 said: Bringing back memories of riding with Dad and the other guys when I was a little kid. When we sold them old trucks we really wanted to get the newer ones at the time, but it sure would be nice to have a few of them around to remember the good ol days !!
  32. 2 points
    CHATTANOOGA, TN, April 9, 2019 — The International Towing and Recovery Hall of Fame and Museum Survivor Fund today announced a new benefit available to those going through the tragedy of losing someone in the line of service. The new Experienced Owners Group (EoG) will allow company owners the opportunity to seek guidance from someone who has been in their current position. The Experienced Owners Group aims to provide this support for company owners who are dealing with the ramifications of losing an employee on the job. For over ten years, the Survivor Fund has been providing financial assistance to families in their time of need when on the job tragedies occur. Now, the Survivor Fund is branching out to focus on another type of Survivor, the company owner. There are many challenges faced by company owners when an operator is killed on the job. The Survivor Fund does not have all of the answers but we do have a powerful list of those who have been in this position and who are willing to speak to anyone with a similar need. The EoG is made up of towing and road service industry company owners who have had an on the job death and are willing to speak to others going through a similar loss. These owners will neither be competitors nor will they be a legal team. The museum, the Survivor Fund and our Experienced Owners Group are not able to provide answers to legal questions. This group is here for moral support and to help with information on how each person may have dealt with their own business tragedy. “The Experienced Owners Group has been in development for several years. During the last year we have seen an increased need and have been told by those involved in the tragedies that this service would be of great benefit,” stated Jeffrey Godwin, Co-Chairman of the ITRHFM Survivor Fund / Wall of the Fallen Committee. “As we begin to rollout a few new Survivor Fund benefits in 2019, supporting of all survivors is our focus.” The process is simple. Today, when a tragedy occurs, the assigned regional representative from the Survivor Fund committee reaches out to the company proactively to offer the assistance of the Fund and information about the Wall of the Fallen. Going forward, the information provided will also include how to participate in the EoG. The rep will endeavor to match the owner with a current tragedy to someone who had a similar incident situation when possible. The committee member will also contact the Experienced Owner being selected and notify them of the need. Both parties will receive an introductions email along with the case information as provided to the Survivor Fund. Once the introduction is made, all communications are direct between the parties and the International Towing and Recovery Hall of Fame and Museum and its Survivor Fund are no longer involved in the interactions. The Experienced Owners Group exists to provide a specialized contact for business owners in their time of need allowing the business owner to speak directly to another business owner who has been through a similar tragedy in their own company. Please note that none of the ITRHFM, the ITRHFM Survivor Fund, the Experienced Owners Group, or the persons involved in these groups are to provide legal advice. If legal advice is required, the inquirer should be steered toward an attorney or other legal professional. To learn more about the Experienced Owners Group, contact Jeffrey Godwin via email at jeffreygodwin@gmail.com. An inquiry / sign up form will be added to the museum website in the Survivor Fund section in the coming weeks. If you have experienced the on the job loss of an employee, please sign-up, get the talking points and serve your fellow towers. About ITRHFM The International Towing and Recovery Hall of Fame and Museum, located in Chattanooga, TN, houses an array of displays and exhibits showcasing the history of towing and recovery. The rotating collection includes early equipment by Manley, Holmes, Vulcan, and Weaver. The Hall of Fame honors individuals who have significantly advanced the industry. The Museum includes a theater, a library, and a gift shop selling souvenirs related to the towing industry. On the outside grounds is the Wall of the Fallen memorial, dedicated to towers who died in the line of service. The ITRHFM Survivor Fund assists the families of the men and women that have made the ultimate sacrifice in the line of service by providing a uniform financial gift at the time of their loss. ITRHFM is a non-profit 501(c)(3) organization and accepts donations for its programs and operations from individuals, corporations and groups. Learn more at www.towingmuseum.com.
  33. 2 points
    Whenever something is being towed, additional securements should always be attached. This doesn’t just apply to wreckers - secondary attachment chains should be attached even hauling a trailer, boat trailer or camper. These chains are there for an obvious reason: to prevent an accident in the event of an attachment failure while towing. But why does WreckMaster insist that the secondary attachments are always crossed? It prevents casualty from veering into traffic Probably the most important information on this list, crossing your chains ensures that the casualty will stay behind your truck in the event of a disconnect from the wheel lift/underrearch. If the chains were parallel and went straight back to the casualty, they would be able to veer and swing freely in both directions and potentially into other vehicles. When the chains are crossed, the casualty is prevented from veering too far in either direction and will instead stay behind the wrecker. NOTE: in the event of a disconnect, be sure to slowly change lanes and reduce speed to avoid the casualty from slamming into the back of the wrecker. It affects turning Secondary attachments can be affected by turning in two ways: You can use the shortest amount of chain and it will make less contact with the ground. If the chains were to be connected parallel and go straight back to the casualty, one of the chains would become too tight whenever turning. For example, when a wrecker turns right, the distance between the left side of the wrecker and the left side of the casualty increases. On the opposite side the chain continues to slack thereby making contact with the ground. By crossing the chains, the amount of chain required is reduced and therefore you will minimize the likelihood of your chains contacting the ground. They Can go above or under the under reach When the chains are crossed, whether they go above or below the wheel lift does not matter. Why is this important? It means that securing to the most logical attachment point becomes easier. Cross the chains over the under reach also helps keep the chains from making contact with the ground while turning. There are benefits to both: Crossing the chains beneath requires more chain but they will not interfere with any other equipment such as towing lights or scratch the under reach. Crossing above can scratch the under reach but requires less chain. or Just be sure that whether you cross them above or below the under reach that they will not interfere with any other pieces of equipment, such as the towing lights. View the full article on WreckMaster.com...
  34. 2 points
    Matjackman

    Matjack 3 Day Factory Class!

    2019 Matjack factory team for the spring session has ended. Thanks to all that participated. Jeff Martin, Howard "scooby" Eagan, Jamie Dougherty, Bruce Pedigo, Dale McLaughlin, Matt Bartlett. #matjackspring2019
  35. 2 points
    Cargo: High end plastic rolls on the side. Thanks to Montague Police and Turners Falls Fire dept, and a special thanks to my great crew, T. J., Bill Wong, Tom Kurtyka Jr., Jake Browning and Samantha Browning, Nice job!!!
  36. 2 points
    I'm here...loud and clear ....😊
  37. 2 points
    Still here in United Kingdom
  38. 2 points
    So many reading and this new system only registers logged in member views. If you're a regular lurker registering has never been easier. Do It Now! Please Doing so will get TowForce closer to a A New Platinum Sponsor that will participate. However, if we cannot reach the 6000 members by June 11th, we prove them right. The Towing & Recovery Industry is just too small of a market for them to expand into. This potential new sponsor wants to get you to their website as they introduce new products. The have also agreed to post in the General Equipment forum with the goal of having a dedicated forum. The traffic is here, we just need to get the numbers up. That means both membership and topic participation. The message board had good traffic even after it broke. However, it became like "Read Only". Do not let this community go in that direction. Thanks, Now Reply to the Roll Call.
  39. 2 points
    found a picture of some of the load....not particularly heavy.... just lots of boxes, loose bags of produce....
  40. 2 points
    EdsTowing

    Rollover w/ Plenty Of Rolls....

    We got the job to dispose of the cargo on this job which was like another nice little job. Winched the rolls out & set them on the rollbacks for a local tow to a recycling center... Then delivered the trailer back to the company... We gave up some additional storage after the bill was paid to work out the logistics to get the disposal job. In the end it was like an additional $6000 on the job so beneficial for us to make it work.
  41. 2 points
    Guy buys this Jeep 2 weeks prior...700 mi on it...then drives 60 mph+ in a 25 mph community zone. Fails to negotiate the curve and tumbles through 4 different properties.... Cops found the guy 1/2 mile away drunk sitting in the middle of the road in his underwear.... Now THAT"S a party... LoL Made junk of his new truck... It was @ 2am in the rain so Eddie grabbed the Jeep and we went back on a Sunday am to do a complete clean up. 2 of the home owners that we talked to were very pleased that we came back and cleaned up all the parts, trees & landscaping.
  42. 2 points
    Lately I am running into more and more 12 point 3/8 drive line bolts that the heads are rounded off before I start to remove them. I found instead of trying a chisel or vice grips, I smash the edge of the bolt head with a hammer and then hammer the socket on and usually that gets them off without the socket spinning on the bolt head. Just a tip I thought I would share.
  43. 2 points
    GRUMPS The Towman

    Snow day

    during major storms and emergencey declarations there are times where as long as the vehicle is well out of the way of traffic, law enforcement / first responders will remove the occupants and examine the vehicle to make sure no one is inside of it then place the caution tape across the vehicle so others who may come across it will know that the vehicle has been cleared of occupants. then the vehicle is usually left there untill the weather event is over then recovered.
  44. 2 points
    Wow!!.....where does the time go?? Matt's now 27 and still hangs a bit with old dad. We are both members of the Race Recovery Team (formerly Miller Race Recovery) at MIS. Matt is an engineer at FCA Chrysler in the SRT division doing engine calibration for Hellcats and Demons. Its his dream job!
  45. 2 points
    rreschran

    Re: New Years Awareness

    Hi All ... just a note to wish you all a very Happy and prosperous New Year. Tonight and tomorrow are those nite and days where the merriment and ignorance of others calls for 110-percent awareness on your part. While not seeming to sound like the proverbial Mother Hen, keep your wits about you and be aware of your surroundings, to include having an escape path and most importantly, stay off the white line. If you can help block for another tower, please do so as you remember the responsibilities and liabilities of blocking. In my area it calls for possible snow and ice in the next 24-hours, and I know that's the reality across the US and Canada. I want you to know I'm committed to continuing to help bring the word of pride, professionalism and safety to the towing and recovery industry by working to uphold those who consider themselves Varsity players. Christine and I pray for your continued safety and look forward to seeing you here and about next year. Believe in what you do as you're all heroes to me. Happy New Year and safe travel. R&C
  46. 2 points
    Funny as hell but joking aside, it might have saved them from a big ticket and costly environmental cleanup, depending on area. Maybe that dispatcher's previous region was California, Richard
  47. 2 points
    EdsTowing

    MD Recovery On Rack Body Truck

    "Nice. Is this the same guy from last year?" No...LoL Funny you brought that up. He left this past summer....I told the fleet manager that we were going to have a little party for him - felt it was the least we could do for all of his support! Then yesterday my son told me he got fired from his new job which was driving a gas truck for a company closer to his home. So we can only hope he comes back to here.... 🤣
  48. 2 points
    EdsTowing

    MD Recovery On Rack Body Truck

    Got a call for a tank delivery truck stuck in the mud. I thought it was going for the F550 but realized different when I pulled on scene... So the 1st thing I had to say was "Do you realize it has rained steady for 2 days which melted all the snow?" This was obviously a bad idea... When they got this truck, I saw that winch & thought they would get themselves in trouble with that. They winched themselves forward and just got deeper... Backed in & set up on an exposed root that I figured would help me from sinking. 2 part line to the heavy crossmember of the lift gate assembly. Pulled it to me & out of the deep holes. Truck was lame & still couldn't move. So I pulled ahead and set my block on a tree to get it closer. Then strait lined it to the edge if the driveway.
  49. 2 points
    Proud employee from Ted's Towing Service, Baltimore, MD stopped by the PolyBody® booth at the American Towman Exposition last weekend to share this photo of there truck with the PolyBody® PG- 180 tandem axle replacement body. Thanks for sharing! For more information on UPF PolyBody® replacement bodies, please contact pcahill@unitedplastic.com and drossetti@unitedplastic.com and learn more about the different styles for light, medium and heavy duty replacement bodies!
  50. 2 points
    Another Metro Tow Trucks RTR50SL Getting Ready to Head to South Africa [emoji1221]! The Best Value on the Market Penetrating Markets World Wide[emoji288]! Metro's versatile RTR-50, designed for heavy duty, reaches the perfect balance between size and capacity. With the 360° continuous motion and the sliding option this unit can reach and lift in any situation you will encounter! For more information please don't hesitate to contact us directly at 1-613-862-1625 or toll free at 1-866-924-1675. Thanks Al Sent from my SM-N960W using Tapatalk
This leaderboard is set to New York/GMT-04:00
×
×
  • Create New...